SuperLift 4″-6″ Lift Kit with Bilstein Shocks for 1993-1999 GMC/Chevy 1500 w/ 3 Bolt Idler Arm 4WD (including 2500 6-Lug)
Description
4″-6″ GM Suspension Lift Kit with Bilstein Shocks – 1993, 1994, 1995, 1996, 1997, 1998, 1999 Chevy/GMC 1500 w/ 3 Bolt Idler Arm 4WD (including 2500 6-Lug)
Part: K270B
- Retains factory ride quality, steering geometry, and CV axle angles
- Load bearing bracketry is made of .25″ thick plate steel or DOM tubing
- Front differential housing does not require trimming
- Centerlink stabilizing system makes steering more responsive and extends pitman/idler arm life
- Shocks included
- Lifetime Warranty
- Satisfaction Guarantee
Tire and Wheel Info
35 x 12.50 on a wheel with up to factory backspacing
IMPORTANT DISCLAIMER: The provided tire/wheel fitments are approximate.
Actual dimensions of a given tire size can vary considerably from one brand to another.
Manufacturers’ wheel offset and backspacing measurement points are not always consistent.
Backspacing greatly impacts tire-to-fender clearance when turning.
Wheel width and backspacing influence whether the tires protrude past the fenders, and to what extent.
Considering these important factors, we recommend that you fit-check your tire/wheel selection prior to purchasing.
Installation Notes
1997 and newer models with Autotrac require dual cardan driveshaft, shown in options. Non-Autotrac models may also need driveshaft if regularly driven in 4WD over 35 MPH.
With single exhaust, a new, reformed section of exhaust crossover pipe is required to clear front driveshaft.
Special puller tool is recommended to load / unload torsion bars.
Also fits 2500 6 Lug models
Installation Instructions
Product Overview
Laser-cut bracketry lowers the factory upper and lower control arms, in relation to the frame, to provide front lift. A 4″ to 6″ front lift range is afforded by the adjustable factory torsion bars; rear lift is via 4″ blocks. Full-width tubular crossmembers attach to the front/upper and rear/lower control arm relocation brackets to further enhance system rigidity. These tubular crossmembers also support the front differential, which is relocated to alleviate CV axle and driveshaft angles. Kicker braces span from the rear tubular crossmember to the vehicle’s frame. A Superlift front skidplate bolts to the front frame crossmember then connects to the factory differential skidplate.
Steering linkage geometry is addressed by a replacement “dropped” centerlink that keeps the tie rods in phase with the lower control arms. Dual stabilizing links prevent fore and aft movement of the centerlink, otherwise, excessive stress loads would be transmitted to the factory pitman and idler arms. The torsion bar crossmember is lowered to align it with the lower control arms. The system includes your choice of Superide or Superide SS shocks by Bilstein.
An optional steering stabilizer kit is also available.
Fitment Table
Year Range | Make | Model | Drivetrain | Engine | Cab |
1993-1998 | Chevy/GMC | 1500 Pickup | 4WD | ||
1993-1999 | Chevy/GMC | 1500 Suburban | 4WD | ||
1995-1999 | Chevy/GMC | 1500 Tahoe / Yukon | 4WD | 2-Door | |
1993-1994 | Chevy/GMC | Blazer / Jimmy (Fullsize) | 4WD |
Be the first to review “SuperLift 4″-6″ Lift Kit with Bilstein Shocks for 1993-1999 GMC/Chevy 1500 w/ 3 Bolt Idler Arm 4WD (including 2500 6-Lug)”
Questions and answers of the customers
-
Do you ship also to Europe (Austria) ? What could be the shiping and Customs rate to Austria ? Thank you
-
Q Do you ship also to Europe (Austria) ? What could be the shiping and Customs rate to Austria ? Th...... Read moreThere are no answers for this question yet. Answer now
Reviews
There are no reviews yet.