Generic filters
Exact matches only
Archives

on

Synergy Rear Track Bar Relocation Bracket 2-3″ Lift for 2020+ Jeep Gladiator JT

Synergy MFG’s Jeep Gladiator JT Rear Track Bar relocation bracket restores your factory handling by raising your vehicles roll center. This bracket will increase the factory track bar mounting location up 3 inches, allowing you to run a stock rear track bar at 3.5 inches of lift height.

Fitments:

  • 2020+ Jeep Gladiator JT

Benefits:

  • Centers rear axle without requiring a new track bar for 2-3 inch lifts
  • Improves rear track bar geometry to reduce the rear end wag experienced with a steep track bar angle
  • Reduces body roll and improves handling
  • Prevents interference between the rear driveshaft and gas tank skid when used with long travel shocks

Features:

  • Raises rear track bar mounting location on the axle by 3.5 inches to raise the vehicle’s roll center
  • Ties into stock track bar bracket in multiple locations for improved strength and durability
  • Laser cut and CNC formed from a combination of 3/16 and 1/4 inch steel for the optimum combination of strength, durability, and performance
  • No cutting or drilling required
  • Features an abrasion-resistant powder coat finish for maximum durability and corrosion resistance
  • 100 percent bolt-on components assures an easy, trouble free installation with the use of basic hand tools

Notes:

  • Must run a minimum 2 inches of bump stop spacing
  • Adjustable rear track bar recommended to be added for lifts 3 inches and taller

pdf-icon.gifInstallation Instructions

  
Prop. 65 Warning for California ResidentsMore information: www.p65warnings.ca.gov
6

on

The Synergy Ford Super Duty F-250 / F-350 / F-450 / F-550 / F-600 front leveling springs lift the front of the truck 2.5”. The springs are progressively wound to provide a soft ride while increasing bottoming resistance. When used in the Synergy Leveling Kit, they provide 9 ¾“ of travel.

Fitments:

Part # Description
8663-25 Synergy 2005+ Ford Super Duty F-250 / F-350 / F-450 / F-550 / F-600 4×4 – Diesel
8664-25 Synergy 2005+ Ford Super Duty F-250 / F-350 4×4 – Gas

Benefits:

  • Increased bottoming resistance
  • Increased travel
  • Fits in stock location
  • No modifications required to install

Features:

  • Hot formed, made from 5160H spring steel 
  • Suspension components feature an abrasion-resistant powder coat finish for maximum durability and corrosion resistance
  • Proudly made in USA
  • Pre-Set. This means no spring sag for the life of the spring
  • Dual rate
  • Sold in Pairs

Notes:

  • Compatible with the 2.5 inch Leveling Kit
  • Only compatible with 4×4 front axle
  • Solid Height: 10 ¼“
  • Free Length: 22”
  • Not compatible with trucks equipped with Front Suspension Height Sensor. This sensor must be removed or the linkage arm lengthened, or damage may result.
Prop. 65 Warning for California ResidentsMore information: www.p65warnings.ca.gov
2

on

Synergy Front & Rear Lower Shock Mount Relocation Kit for 2020+ Jeep Gladiator JT

Synergy Front Lower Shock Extension Brackets for 2018+ Jeep Wrangler JL/JLU, 2020+ Jeep Gladiator JTThe Synergy Jeep Gladiator JT Lower Shock Relocation Kit move the mounting points of your factory shocks up 2 inches from the stock location. These brackets are perfect when lifting your Gladiator JT 2 inches and want to retain your stock shocks. They are a bolt-on design for easy install and retain the stock strength and bracket geometry.  

Fitments:

  • 20+ Jeep Gladiator JT

Benefits:

  • Raises lower shock mounts for increased ground clearance and moves shocks out of harm’s way since the stock shock mounts are prone to extreme trail abuse from low clearance
  • Allows for the stock shocks, such as the Mojave, to be retained for a 2 inch lift without sacrificing suspension travel
  • Bolt-on design

Features:

  • Manufactured from laser cut 3/16 inch steel and CNC bent for superior durability
  • Suspension components feature an abrasion-resistant powder coat finish for maximum durability and corrosion resistance
  • 100 percent bolt on components assures an easy, trouble free installation with the use of basic hand tools

Includes:

Notes:

pdf-icon.gifFront Installation Instructions

pdf-icon.gifRear Installation Instructions

Prop. 65 Warning for California ResidentsMore information: www.p65warnings.ca.gov
6

on

The Synergy Jeep Gladiator JT control arm and track bar hardware kit replaces all your suspension link hardware with grade 8 nuts, bolts and nut tabs. We use an increased bolt diameter to reduce the sloppy factory hardware tolerances. This kit is great when upgrading your control arms or refreshing your build..

Fitments:

Part # Fitment Location
8850-05 2018+ JL, JLU Wrangler, 2020+ Jeep JT Gladiator Front JL & JT Control Arm and Track Bar Hardware Kit
8850-07 Fits: 2020+ Jeep JT Gladiator Rear JT Control Arm Hardware Kit
8850-04 Fits: 2020+ JT Gladiator Full Control Arm and Track Bar Hardware Kit

Benefits:

  • High strength G8 hardware
  • Includes Front and Rear Track Bar Bolts
  • Increased bolt diameter to reduce sloppy factory tolerances
  • Replaces the Upper and Lower Control Arm bolts and specialized nut tabs
  • Includes hardened extra thick washers that will not deform or contort like standard washers
  • Complete Kit available to replace every suspension link bolt on your JT!

Kits Include:

8850-05
Front JL & JT Control Arm and Track Bar Hardware Kit
8850-07
Rear JL Control Arm Hardware Kit
8850-04
Full Control Arm and Track Bar Hardware Kit
(4) – Grade 8 Front Lower Control Arm Bolts
(4) – Grade 8 Front Upper Control Arm Bolts
(2) – Grade 8 Front Track Bar Bolts
(9) – Grade 8 Top Lock Nuts
(1) – Grade 8 Top Lock Flag Nut for Front Track Bar
(19) – Extra Thick Grade 8 hardened Flat Washers		 (8) – Grade 8 Rear Control Arm Bolts
(9) – Grade 8 Top Lock Nut
(19) – Extra Thick Grade 8 Hardened Washers
(2) – Grade 8 Rear Track Bar Bolts
(1) – Grade 8 Top Lock Nut Tab for Rear Track Bar		 (4) – Grade 8 Front Lower Control Arm Bolts
(4) – Grade 8 Front Upper Control Arm Bolts
(8) – Grade 8 Rear Control Arm Bolts
(4) – Grade 8 Front and Rear Track Bar Bolts
(18) – Grade 8 Top Lock Nut
(2) – Grade 8 Top Lock Nut Tab for Track Bars
(38) – Extra Thick Grade 8 Hardened Washers

Note:

  • 8850-04 is a group part number that pulls Quantity (1) 8850-05 and (1) 8850-07 

pdf-icon.gifInstallation Instructions

Prop. 65 Warning for California ResidentsMore information: www.p65warnings.ca.gov
5