OME Front 1.5-3″ Lift Coils for 1995-2004 Tacoma, 1996-2002 4Runner
Front OME Coils for 1995-2004 Tacoma and 1996, 1997, 1998, 1999, 2000, 2001, 2002 4Runner
As part of their integrated 4WD suspension systems, Old Man Emu designs a range of coil springs for each vehicle, enabling the installer to match the most appropriate springs to the intended application. While ride height increases are attained, emphasis is placed on ride control improvements. Further fine tuning is achieved when the springs are matched to a corresponding set of Old Man Emu shock absorbers, delivering a fully integrated system designed specifically to suit your vehicle.
- Springs are formed on precision mandrels
- Scragging before and after shot peening to prevent sagging
- Coil spring end configurations designed to exact specifications guaranteeing perfect fitment to your vehicle
- Durable powder coat finish
Front coils: Choose one option in dropdown
- OME 2880: Stock front weight.1.5 inch lift.
- OME 2881: Stock front weight. 2-2.5 inch lift.
- OME 2883: 200 + lbs additional front weight (heavy bumper and winch) 2.5- 3 inch Lift
**2wd Prerunner lift heights may vary. 2881 and 2883 coils are not recommend for 2wd without additional weight.
NOTE: 2883 coils require matching OME 90004 front shocks
Sold in pairs.
Will not work on a 5-lug Tacoma.
Want a full lift kit?
Questions and answers of the customers
Just installed General Spring HD leafs and am sitting lower in the front. Need about 1.5 lift so going with the 80s. If I pair these with the Bilstein 5100s what setting should they be at? 96 tacoma 6 lug standard weight
Q Just installed General Spring HD leafs and am sitting lower in the front. Need about 1.5 lift so ...... Read more answer nowA In order to figure out how much lift you need to level please take existing measurements from center of the wheel hub to the bottom of the fender. Difference between front and rear is how much lift you need to level. https://www.suspensionlifts.com/level.png for lifted coils it's usually recommended to use the lowest notch adjustment
I have an ARB front bumper that weighs about 260 lbs and was wondering if I should get 883s for the front to achieve and maintain 2" lifts all around? I'm afraid if I go with the 883s and my bumper isn't heavy enough that I will have a lift that is higher than the 2" that I want.
Q I have an ARB front bumper that weighs about 260 lbs and was wondering if I should get 883s for t...... Read more answer nowA I think you would be fine going with the 883s. I have them on the front of my 3rd gen paired with 5100s and my front bumper weighs about 80ish pounds and im at about 2.5 inches of lift. Your bumper will definitely be heavy enough.
I have the bilstein adjustable 5100 set at about 1” of lift if I get the 2.5” coils will I sit at 3.5” of lift
- I have a 4cyl 95 4wd single cab Tacoma with a 100lb winch/bumper. I'd like 3" of lift with bilstein 5100s. Which OME coils should I get and on which setting should the bilsteins be set on?
Q I have a 4cyl 95 4wd single cab Tacoma with a 100lb winch/bumper. I'd like 3" of lift with bilste...... Read more answer nowA We can offer front 5100 shocks https://www.suspensionlifts.com/shop/toyota-tacoma/1995-2004/front-lifts-and-coilovers-95-04-tacoma/front-bilstein-height-adjustable-5100-shocks-for-1995-2004-toyota-tacoma-and-4runner/ and OME 2883: 200 + lbs additional front weight (heavy bumper and winch) 2.5- 3 inch Lift https://www.suspensionlifts.com/shop/toyota-tacoma/1995-2004/front-lifts-and-coilovers-95-04-tacoma/front-ome-coils-1995-2004-toyota-tacoma-1996-2002-toyota-4runner/ But with such a spring, the front shocks must be used with the ring on the shock at its lowest position. otherwise the shock will break
How can I get 4 inches of lift
Q How can I get 4 inches of lift answer nowA you can add body lift
what setting should I put 2881's on Bilstein 5100's, 1st, 2nd, 3rd or 4th? For 2wd 98 4runner
Q what setting should I put 2881's on Bilstein 5100's, 1st, 2nd, 3rd or 4th? For 2wd 98 4runner
For a 98 2wd 4runner with 5100's already installed, would the 2880 or 2881's be the best choice for a 2.5-3in lift? I'm trying to swap out the stock ones, since I currently use these with the 5100's at the highest setting. Looking to upgrade the coil springs only
- What would be the best option for a 2wd 98 4runner? What could I do then to get a 2.5-3in lift in the front with 5100's?
Q What would be the best option for a 2wd 98 4runner? What could I do then to get a 2.5-3in lift in...... Read more answer nowA We can offer Bilstein B8 5100 (Ride Height Adjustable) shock absorbers https://www.suspensionlifts.com/shop/toyota-4runner/1996-2002/shocks-96-02-toyota-4runner/bilstein-5100-0-2-3-lift-front-shocks-1996-2002-toyota-4runner-4wd/ Can work with stock springs and get different lift heights Installation Instructions https://productdesk.cart.bilsteinus.com//media/products/bilstein/E4-WM5-Y485A00_1.pdf or we can offer https://www.suspensionlifts.com/shop/toyota-4runner/1996-2002/shocks-96-02-toyota-4runner/bilstein-0-2-3-front-lift-6112-series-shocks-coil-kit-1996-2002-toyota-4runner-4wd/
What is the best pair of shocks for these, the 5100?
Q What is the best pair of shocks for these, the 5100? answer nowA You can use 5100s or OME
Are the coils sold in pairs or single
Q Are the coils sold in pairs or single answer nowA Sold as pair
I have a 2000 Prerunner Tacoma. And it said that the 2883 are not recommended for 2WD and does that include the prerunners. Just making sure I am understanding it.
- If I get the 2880 coils to replace with my old coils, can I still add a 6in lift later? or will I have to put the old coils back on it?
- Can I use the 2880 springs with the 5100 shocks set at zero, and still have a 6in lift kit?
Q Can I use the 2880 springs with the 5100 shocks set at zero, and still have a 6in lift kit? answer nowA it's not recommended to stack lifts
Can the 2883 fit on a bilstein 2.5 inch lift shock or any other shock?
You guys are out of stock on the OME 90004 front shocks.
Q Can the 2883 fit on a bilstein 2.5 inch lift shock or any other shock? You guys are out of stock ...... Read more answer nowA I have the Bilstein 5100's shocks front and back and I paired it with the OME 883s front and 891 rear which fits fine. Its a bit rough due to the heavier duty weight capacity but I'm not driving it as a mall crawler so I'm okay with it.
I would like to install the 2883 and 2895E with the bilstein 5100 to achieve a 2" lift for the front and 1.75" to level out on a '19 4runner. I may add a gobi rack, c4fab low profile grill in the future. Planning to use this for daily driving n light overlanding. Anyone have thoughts on this? TIA
- If I put 881 springs on 5100 bilstein lowest setting I will get 2inches plus from stock? I only want 2 inches max from stock height 98 Tacoma prerunner
- Is there any reason it would be bad to get the 883 springs for a 3rd gen 4runner if it doesnt have an after market bumper yet
- I currently have Bilstein 5100 (24-188265) shocks in the front with tundra coils and i sit at a 2 inch lift, could i just add these coils to gain the 3 inch lift in the front or do i need to get different shocks as well?
Q I currently have Bilstein 5100 (24-188265) shocks in the front with tundra coils and i sit at a 2...... Read more answer nowA https://www.suspensionlifts.com/shop/toyota-tundra/00-06-toyota-tundra/front-lifts-and-coilovers-00-06-toyota-tundra/bilstein-height-adjustable-5100-shocks-for-2000-2006-toyota-tundra/ If you have these shocks, then they should work with stock springs. Rearranging the ring in shock, you get a different lift Installation Instructions https://productdesk.cart.bilsteinus.com//media/products/bilstein/E4-WM5-Y517A00_1.pdf If you are not using a stock coil, the rings should be installed in the lower position This coil is not fit for TUNDRA
I have Rancho RS9000XL quick lift struts (1.5") on my truck but have a heavy bumper and winch, causing the tires to rub. Which model of these springs will fit with those shocks properly?
- Stock weight on 2004 Tacoma 4WD. I have Bilstein 5100 up front with stock springs on top setting. Looking to replace springs but keep the same ride height. What spring is recommended and at what setting? Thanks.
- Does this work with 24-188265 blistein 5100 series? Does this match to have a nice ride with the Light Duty 2″ Lift OME 906 Rear Coils
- Will those coil springs fit fabtech shocks?
Q Will those coil springs fit fabtech shocks? answer nowA These coils need shocks that are longer then stock
I have a 2001 single cab 4cyl 4X4 tacoma with ARB bull bar. I'm looking at getting OME 883's do I need the Bilstein 5100 adjustable shocks instead of the stock shocks? I'm wanting to go the full 3 inches of lift.
- What struts will I need with 883's to get a 3 inch lift? Can you attach a link please?
Q What struts will I need with 883's to get a 3 inch lift? Can you attach a link please? answer nowA Longer shocks will be needed * * * https://suspensionlifts.com/shop/toyota-4runner/1996-2002/front-bilstein-height-adjustable-5100-shocks-for-1995-2004-toyota-tacoma-and-4runner/ * * *
Will these work on a 2000 Tacoma SR5 that has a 5 Lug Wheel?
Q Will these work on a 2000 Tacoma SR5 that has a 5 Lug Wheel? answer nowA Unfortunatelly no, these coils are for 6-lug. For 5-lug we can offer only few items * * * https://suspensionlifts.com/product-category/toyota-tacoma/1995-2004/1995-2004-5-lug-tacoma/
If I already have a 3 leveling kit and I have a custom bumper I built but would you recommend running the 883 springs I really don't care to much about ride quality as much as I do scrubing since I put the bumper on but dose the springs already have lift built in them
Q If I already have a 3 leveling kit and I have a custom bumper I built but would you recommend run...... Read more answer nowA OME 883 coils will give you 2.5- 3 inch Lift with 200 + lbs additional front weight (heavy bumper and winch) It is not recommended to stack lifts - having more then 3'' of lift can damage the cv axles and suspesion, so the leveling kit may need removing.A So will I have to run the shocks as well
is there a version that will work with 5 lug lo lift 1.5"
Q is there a version that will work with 5 lug lo lift 1.5"
What is the spring rate for the 881?
Q What is the spring rate for the 881? answer nowA 500 pound spring rate, the same as what the 880 spring rate is. The 881 springs are slightly longer, hence the greater lift with them.
I installed a lift a few years ago, don't drive the truck very much, or haven't since installing the lift. 2004 Tacoma Xcab 4x4 w/ARB bullbar, milemarker hydraulic winch. Wearing tires with 881 and nitrogen OME sport shocks. Just changed over to 880 and same springs but looks like truck sank down and still feels the same. At time of install 883's were not recommended for 4cyl truck, Has something changed? What type strut do you run with the springs and how is the ride?
- I have a 2001 Tacoma double cab 4x4 with adjustable bilstein 5100's. My factory springs are shot and I'm looking for a spring to give me ~2.5" of front lift.
- do these work with stock shocks or will upgrade be needed? what tire size will be able to be used for a 2002 4runner sr5 2wd?
Q do these work with stock shocks or will upgrade be needed? what tire size will be able to be used...... Read more answer nowA It'll depend on your truck front weight. most likely the shocks upgrade will be needed to provide additional suspension travel for the lift size closer to 3''. As for your tire question - unfortunately we haven't tested tire sizes on that lift and do not have tire size information for that, but with the 3'' lift and proper shocks the whole wheel diameter can probably be increased by 2''. It'll depend on the tires and rims you will use and will need test fitment.